Variable Stiffness Actuators prove invaluable for robotics applications in unstructured environments, fostering safe interactions and enhancing task adaptability. Nevertheless, their mechanical design inevitably results in larger and heavier structures compared to classical rigid actuators. This paper introduces a novel 3 Degrees of Freedom (DoFs) parallel wrist that achieves variable stiffness through redundant elastic actuation. Leveraging its parallel architecture, the device employs only four motors, rendering it compact and lightweight. This characteristic makes it particularly well-suited for applications in prosthetics or humanoid robotics. The manuscript delves into the theoretical model of the device and proposes a sophisticated control strategy for independent regulation of joint position and stiffness. Furthermore, it validates the proposed controller through simulation, utilizing a comprehensive analysis of the system dynamics. The reported results affirm the ability of the device to achieve high accuracy and disturbance rejection in rigid configurations while minimizing interaction forces with its compliant behavior.

Small-scale robots offer significant potential in minimally-invasive medical procedures. Due to the nature of soft biological tissues, however, robots are exposed to complex environments with various challenges in locomotion, which is essential to overcome for useful medical tasks. A single mini-robot often provides insufficient force on slippery biological surfaces to carry medical instruments, such as a fluid catheter or an electrical wire. Here, for the first time, we report a team of millirobots (TrainBot) that can generate around two times higher actuating force than a TrainBot unit by forming a convoy to collaboratively carry long and heavy cargos. The feet of each unit are optimized to increase the propulsive force around three times so that it can effectively crawl on slippery biological surfaces. A human-scale permanent magnetic set-up is developed to wirelessly actuate and control the TrainBot to transport heavy and lengthy loads through narrow biological lumens, such as the intestine and the bile duct. We demonstrate the first electrocauterization performed by the TrainBot to relieve a biliary obstruction and open a tunnel for fluid drainage and drug delivery. The developed technology sheds light on the collaborative strategy of small-scale robots for future minimally-invasive surgical procedures.

Principal component analysis is commonly used for dimensionality reduction, feature extraction, denoising, and visualization. The most commonly used principal component analysis method is based upon optimization of the L2-norm, however, the L2-norm is known to exaggerate the contribution of errors and outliers. When optimizing over the L1-norm, the components generated are known to exhibit robustness or resistance to outliers in the data. The L1-norm components can be solved for with a binary optimization problem. Previously, L1-BF has been used to solve the binary optimization for multiple components simultaneously. In this paper we propose QAPCA, a new method for finding principal components using quantum annealing hardware which will optimize over the robust L1-norm. The conditions required for convergence of the annealing problem are discussed. The potential speedup when using quantum annealing is demonstrated through complexity analysis and experimental results. To showcase performance against classical principal component analysis techniques experiments upon synthetic Gaussian data, a fault detection scenario and breast cancer diagnostic data are studied. We find that the reconstruction error when using QAPCA is comparable to that when using L1-BF.

The physical coupling between robots has the potential to improve the capabilities of multi-robot systems in challenging manufacturing processes. However, the path tracking accuracy of physically coupled robots is not studied adequately, especially considering the uncertain kinematic parameters, the mechanical elasticity, and the built-in controllers of off-the-shelf robots. This paper addresses these issues with a novel differential-algebraic system model which is verified against measurement data from real execution. The uncertain kinematic parameters are estimated online to adapt the model. Consequently, an adaptive model predictive controller is designed as a coordinator between the robots. The controller achieves a path tracking error reduction of 88.6% compared to the state-of-the-art benchmark in the simulation.

The development of miniature joint angle sensors is a crucial factor for the successful utilisation of various robotic applications in the healthcare and many other industries. This includes applications such as continuum robots used in minimally invasive surgery (MIS), prosthetics, wearable flexible devices, and many more [1]. Joint angle sensing in these applications, or more broadly, shape sensing, is required to accurately actuate and measure tip position and curvatures made by these robotic devices. To do this, a number of miniaturised joint angle sensors have been developed for integration into these applications, uti-lising various sensor types. Some examples include inertial, stretch, and FBG-based sensors [2].

To effectively implement quantum algorithms on noisy intermediate-scale quantum (NISQ) processors is a central task in modern quantum technology. NISQ processors feature tens to a few hundreds of noisy qubits with limited coherence times and gate operations with errors, so NISQ algorithms naturally require employing circuits of short lengths via quantum compilation. Here, we develop a reinforcement learning (RL)-based quantum compiler for a superconducting processor and demonstrate its capability of discovering novel and hardware-amenable circuits with short lengths. We show that for the three-qubit quantum Fourier transformation, a compiled circuit using only seven CZ gates with unity circuit fidelity can be achieved. The compiler is also able to find optimal circuits under device topological constraints, with lengths considerably shorter than those by the conventional method. Our study exemplifies the codesign of the software with hardware for efficient quantum compilation, offering valuable insights for the advancement of RL-based compilers.

This study introduces an innovative design for a Variable Stiffness 3 Degrees of Freedom actuated wrist capable of actively and continuously adjusting its overall stiffness by modulating the active length of non-linear elastic elements. This modulation is akin to human muscular cocontraction and is achieved using only four motors. The mechanical configuration employed results in a compact and lightweight device with anthropomorphic characteristics, making it potentially suitable for applications such as prosthetics and humanoid robotics. This design aims to enhance performance in dynamic tasks, improve task adaptability, and ensure safety during interactions with both people and objects. The paper details the first hardware implementation of the proposed design, providing insights into the theoretical model, mechanical and electronic components, as well as the control architecture. System performance is assessed using a motion capture system. The results demonstrate that the prototype offers a broad range of motion ($[55, -45]${\deg} for flexion/extension, $\pm48${\deg} for radial/ulnar deviation, and $\pm180${\deg} for pronation/supination) while having the capability to triple its stiffness. Furthermore, following proper calibration, the wrist posture can be reconstructed through multivariate linear regression using rotational encoders and the forward kinematic model. This reconstruction achieves an average Root Mean Square Error of 6.6{\deg}, with an $R^2$ value of 0.93.

We present a new fab-in-the-loop reinforcement learning algorithm for the design of nano-photonic components that accounts for the imperfections present in nanofabrication processes. As a demonstration of the potential of this technique, we apply it to the design of photonic crystal grating couplers fabricated on an air clad 220 nm silicon on insulator single etch platform. This fab-in-the-loop algorithm improves the insertion loss from 8.8 to 3.24 dB. The widest bandwidth designs produced using our fab-in-the-loop algorithm can cover a 150 nm bandwidth with less than 10.2 dB of loss at their lowest point.

Ford's new Trailer Hitch Assist feature has been programmed using AI machine learning to allow a pickup to drive in reverse and line up its hitch with a trailer. Towing trailers is one of the main reasons people buy pickups, but it can also be one of the most challenging things to do with them. Driving a truck in reverse with a trailer attached is a skill that requires a lot of practice, and just getting a hitch lined up to connect in the first place is tricky. The latter is especially true when you're by yourself, even with the rearview cameras that come standard on vehicles today. Now, Ford has technology that lets its trucks do it for you, but it takes some training.

We propose the combination of forward shape derivatives and the use of an iterative inversion scheme for Bayesian optimization to find optimal designs of nanophotonic devices. This approach widens the range of applicability of Bayesian optmization to situations where a larger number of iterations is required and where derivative information is available. This was previously impractical because the computational efforts required to identify the next evaluation point in the parameter space became much larger than the actual evaluation of the objective function. We demonstrate an implementation of the method by optimizing a waveguide edge coupler.